SWC Forums

Pull up a chair...let's talk fishing.

Notifications
Clear all

Lockwood Folly Dredge Schedule

54 Posts
13 Users
0 Reactions
22.5 K Views
Capt Ryan Jordan
(@pin)
Honorable Member
Joined: 21 years ago
Posts: 466
 

Dredge is there and is getting the job done. They are cutting to the west of the marked inlet now and blowing sand into the current one. If you are heading out give them a call on 13 and make sure you are in deep enough water and DON"T follow the cans they are wrong. They said they are already trying to get the buoy tender here ASAP.



   
ReplyQuote
(@curmudgeon)
Noble Member
Joined: 21 years ago
Posts: 1317
Topic starter  

Good deal. Hope they at least get the cans right before Labor Day even if they can't get a survey issued. Otherwise, the marine assistance service of choice could get really busy ... :shrug:



   
ReplyQuote
Wes Livingston
(@wes)
Noble Member
Joined: 22 years ago
Posts: 968
 

That's good news. Thanks for the report



   
ReplyQuote
Steve Hamilton
(@)
New Member
Joined: 16 years ago
Posts: 1
 

Merritt was in the inlet today. Talked to the captain, he expects to there for 2 weeks.



   
ReplyQuote
Michael Ducey
(@mducey)
Eminent Member
Joined: 16 years ago
Posts: 18
 

Saw the dredge there on the Saturday the 17th



   
ReplyQuote
nathan justice
(@)
Estimable Member
Joined: 14 years ago
Posts: 198
 

I am in the area and I heard it was working and the new channel is to the West.



   
ReplyQuote
Charlie
(@)
Reputable Member
Joined: 15 years ago
Posts: 403
 

Any updates for the Labor Day weekend? Cans in place? Thanks for any update. Charlie



   
ReplyQuote
steve brewer
(@)
Noble Member
Joined: 17 years ago
Posts: 1094
 

Charlie,

Cans were not where the Merritt was dredging last weekend. The dredge was approximately 100-300ft to the right of the cans past the #5 can. Stay right and go slow unless they have moved the cans to the west. Hope you fill the box!



   
ReplyQuote
nathan justice
(@)
Estimable Member
Joined: 14 years ago
Posts: 198
 

Should be dredging through Saturday according to the schedule. You can contact Roger Bullock at the Wilmington Corps of Engineers office. He has always responded timely to my questions about the inlet.

Roger.D.Bullock@usace.army.mil



   
ReplyQuote
Lane Adams
(@)
Prominent Member
Joined: 20 years ago
Posts: 750
 

They were there this morning.

Usually takes a week or two after the dredge leaves before the tender comes to move the buoys.



   
ReplyQuote
Capt Ryan Jordan
(@pin)
Honorable Member
Joined: 21 years ago
Posts: 466
 

Dredge is still working until the 31st. Cans are not in the right place, they moved a few of them but the reds are no where near the right place. Contact the dredge on channel 13 before you go in or out and they will let you know where to go and when it is safe to give a pass. The buoy tender has been contacted when they started to dredge so they hope it will get here soon.



   
ReplyQuote
Charlie
(@)
Reputable Member
Joined: 15 years ago
Posts: 403
 

Stack and Ryan thanks for the update. I think we'll go out of Shallotte point. Going to pull hardware all weekend. Not looking for the big one but some to keep my wife buisy. She has fishing ADD. Get the point. Be on ch 6 sat and sun. Thanks, Charlie



   
ReplyQuote
nathan justice
(@)
Estimable Member
Joined: 14 years ago
Posts: 198
 

I looked at the hydro map published on 8/26 and it is still very shallow at the green can (47A) in the ICW. I hope they are planning on working that area. I will contact the corps and post their response.



   
ReplyQuote
nathan justice
(@)
Estimable Member
Joined: 14 years ago
Posts: 198
 

Anyone run out of Lockwood recently? If so, please let me know the condition of the channel.

Thanks!



   
ReplyQuote
Lane Adams
(@)
Prominent Member
Joined: 20 years ago
Posts: 750
 

It is in good shape. Been running it a least a couple times a week. I still favor the green cans but as long as your on the correct side of the reds you are okay.



   
ReplyQuote
Page 3 / 4
Share: