SWC Forums
Pull up a chair...let's talk fishing.
Very nice!! I'm looking forward to seeing install.
Very nice. I assume you are putting it on your Gamefish 25 and would like to know how it works for you. I have a boat like yours and have been considering that as an option for hovering over bottom spots. Thanks.
Yep, I'm waiting on one too. Got everything ready except the trolling motor. Got the same 25 Gamefish but went with minnkota 87 inch shaft.
If you don't mind sharing, where do you plan to put the batteries? I have limited space in my 2014 and have had trouble fishing wires from the console toward the bow. Seahunt used wire ties and tape along the entire length of the existing bow wiring harness making it impossible to use an existing wire as a pull wire. The chase seems to be filled with foam.
I removed the crapper(which I never use) and hoses except the one from the fresh water pump. (I capped it and pushed it in through the hole it came through.) Figured I could use it to pump the water out for winter storage. I placed a piece of 3/4 Inch starboard big enough to hold (3) battery trays on the floor but used spacers so water wouldn't get trapped under the starboard. I used the existing toilet screw holes to attached the starboard so no new holes were drilled in the floor and the toilet could be reset if I sale. I then made a shelve of equal size that sets on top of batteries as protection but is hinged for easy access. My charger is mounted on top of this shelve. I'm an electrician and can tell you that fishing the wires to the anchor locker was a chore for me. You'll have to remove one of the speakers in the bow and use fiberglass fishing sticks so you can keep them up near the top of the gunnels.
They will get stuck if you don't between the hull and liner. It's definitely a two man job. Push the sticks from the speaker to the front, and pull your wire from the locker. Then push the sticks towards the console and pull the remainder to the console. If you use the macerator hatch in the console you can feel around over the partial bulkhead for the fiberglass rod while someone feeds it. After getting the wires to this location I used the existing hose access to feed the wires to battery location. I've seen where folks close off the macerator access hatch and use it for the battery location by making a starboard shelf. I actually like this area for storing tools, etc. so they don't get wet.
Thanks for sharing the information. I know what you mean about the two man job, I tried replacing the bow speaker wire by myself and wound up cussing the Seahunt engineers for not making a more accessible wire chase. Installing the trolling motor electrical will be a pain, but having that spot lock will be worth it.
If you don't mind sharing, where do you plan to put the batteries? I have limited space in my 2014 and have had trouble fishing wires from the console toward the bow. Seahunt used wire ties and tape along the entire length of the existing bow wiring harness making it impossible to use an existing wire as a pull wire. The chase seems to be filled with foam.
I am mounting the batteries on the shelf inside the center console. I removed the hatch on the deck so it is flat and shaped a 3/4 inch sheet of starboard to fit there. My cables are ran from the anchor locker to the deck in the console using the hole where the hoses are for the head. In addition, I have a 4" pie plate that I am using the access the lever for the macerator. I will post some pix tomorrow.
On a side note. FEDEX dropped my trolling motor on the nose cone and damaged it! Even with the Styrofoam protecting it, they managed to break the seal on the armature and the shaft came through the box. Rhodan told me to send it back to them so they can make it right. Great company=Rhodan. FEDEX, you can do better.
Sorry Ricky. Didn't mean to hijack your thread, just excited to finally be getting my trolling motor. It is supposed to be here tomorrow and it's the last thing I was waiting on. Can't wait to try it out.
Thank you both! Useful tips all around.
You've got me excited now about the prospect of having an anchor mode trolling motor on my boat.
This will be a very cool setup that will get away from the aggravation of shifting winds and currents while anchored.
I assume you are still keeping your plow anchor and windlass and mounting the motor offset on the bow so your plow anchor does not interfere.
No windless for me. But I will be keeping my fortress anchor and about 200 feet of rode on the boat.
I hope y'all share some installation pics. That Track Mode will be the trick for working ledges. Looks like I'm going to be spending some money.
FYI - I use a Cisco fishing TM support for the long shaft TM, very high quality and worth the cost to protect trolling motor along with the fiberglass.
I purchased the Ram claw system. It attaches to the recessed rail and the trolling motor utilizing their claw system so I didn't need to drill any holes. As for the trolling motor mount, I'm using the 9 inch ultra heavy duty Shuttleslide. It allows the whole motor to be within the rubrail of the boat so nothing hangs over until deployed.
Go gett'em Forte!!!

