SWC Forums

Pull up a chair...let's talk fishing.

Custom hatches?
 
Notifications
Clear all

Custom hatches?

16 Posts
6 Users
0 Reactions
40.4 K Views
Barry Turano
(@barryturano)
Famed Member
Joined: 17 years ago
Posts: 2720
Topic starter   [#45642]

Last year I bought a 24' Albemarle center console. This model does not have a pulpit. The anchor is stowed under the forward deck with the only way to get to it was a vertical hatch on the bulkhead. Both the anchor and rode were stowed there.
That was not going to work for me. So I had the running lights moved and replaced, then added a bowsprit and center cleat. I also had the people doing the modifications add a hawse pipe to feed the rode into the locker. They put the cleat aft of the pipe (not where I wanted it). So now you need to bring the rode back over the pipe to cleat it off. It is also one royal PIA to stow the rode.
What I want is to get a hatch about 11x11 with a notch for the rode that can be put behind the center cleat. This way the line does not go back over the pipe, and it will be easier to stow. I have found 1 hatch but I feel it is to large and it will open aft I want something that would open to the side. Here is a link to what is available.

http://greatlakesskipper.com/innovative-product-solutions-m-1119-aw-wr-520-163-11-x-19-arctic-white-boat-anchor-hatch-w-rope-cutout

Can anyone recommend a fabricator that can make something like what is shown but in a 11 x 11 size.



   
Quote
Duane
(@rdnkvet)
Noble Member
Joined: 16 years ago
Posts: 1403
 

You might be able to get help here:

http://www.boatoutfitters.com/custom-boat-doors.html?Attribs=699&catID=97



   
ReplyQuote
Cliff Pack
(@recess)
Eminent Member
Joined: 19 years ago
Posts: 36

   
ReplyQuote
Drew Maultsby
(@)
Prominent Member
Joined: 17 years ago
Posts: 806
 

Let's see a picture of what you have. Aren't there a couple of boat salvage yards in Wilmington? There is a boat junkyard in the Jax Craigslist that you can pick your own parts. Rusty Ron's salvage in MHC has hatches of all sizes.



   
ReplyQuote
Barry Turano
(@barryturano)
Famed Member
Joined: 17 years ago
Posts: 2720
Topic starter  

Here is a picture of what I am looking for/at. http://greatlakesskipper.com/innovative-product-solutions-m-1119-aw-wr-520-163-11-x-19-arctic-white-boat-anchor-hatch-w-rope-cutout I would like it to be hinged on the left side with a pull handle or something on the right. What I want to do is add the hatch to the aft part of the forward deck aft of the cleat. I have attached a picture of the forward deck. I could use the hath in the link but it would open to the stern. I want it to open to port or stbd.p1000923r_268.jpg



   
ReplyQuote
Drew Maultsby
(@)
Prominent Member
Joined: 17 years ago
Posts: 806
 

First, they did the right thing by putting the cleat aft of the hawse, otherwise the rode could snag when the anchor is falling. Some people just 'drop' anchor.
The hawse pipe should be over the deepest part of the rode locker, so that the rode falls in. We all know how hard it is to push a rope, especially when trying to push it through a hole and it has nowhere to go. The deepest part of the locker is probably under where you want the hatch, and I suspect the reason you want it is to help feed the rode to that part of the locker, because there is not enough fall under the hawse pipe.

If I was dealing with the set-up that you have right now, I would have a leash of 3/8 soft braid, with a good snap on the end, and I would snap onto the anchor shackle, or the chain if you use it, and take that to my cleat, and let the rode go in the hawse.
BTW, GLSkipper is one of the most expensive marine vendors on Ebay, and I think you can get a better hatch and a better deal. With anything close to square, you can mount it to open in any direction you chose.
Also from GLS, and you can hinge it on the side you choose, and notch the top, since it is starboard. Maybe too long, but starboard hatches are pretty available.
http://www.ebay.com/itm/PALM-BEACH-MARINE-160812-13-1442-OFF-WHITE-16-X-12-BOAT-ACCESS-HATCH-/400798071251?hash=item5d516d39d3&vxp=mtr

edit again after another read: So you want to eliminate the hawse pie, and cleat off the rode and go straight to the new hatch?

Could you live with beige?
http://www.ebay.com/itm/JET-TECHNOLOGIES-11-5-8-X-11-5-8-BEIGE-PONTOON-BOAT-ARMREST-ACCESS-DOOR-HATCH-/200851663906?hash=item2ec3b12c22

How much room do you have?
http://www.ebay.com/itm/RINKER-208127-TEAK-ISLE-OFF-WHITE-13-5-8-X-9-INCH-BOAT-BATTERY-SWITCH-HATCH-330-/191411246864?hash=item2c90ffd710

Another thing to consider, if your deck is not completely flat, the trim will screw down and conform pretty well, (unless you have a piano hinge on one side), but the door will remain flat, and pop out of the frame. The bigger the hatch, the bigger the problem. Cut a piece of plywood, or lay a piece of 12 by 12 tile on the spot, and see how flat it lays.



   
ReplyQuote
Barry Turano
(@barryturano)
Famed Member
Joined: 17 years ago
Posts: 2720
Topic starter  

Glacierbaze
Square is the best option I would be very happy with it. Biggest concern is the notch. As far as Starboard I read it does not support weight very well. Even though I do not plan on standing on it. You thoughts?!



   
ReplyQuote
Drew Maultsby
(@)
Prominent Member
Joined: 17 years ago
Posts: 806
 

I''m guessing it is 1/4, or 3/8, and weight is not going to be a problem in a 12 x 12. The load bearing problem in both is that the lid rests on the bottom trim, which is only held on by 2 screws per side, unless it is chemically welded, which I doubt. Probably designed for vertical use, definitely not for standing on.



   
ReplyQuote
Rich
 Rich
(@squid-row)
Illustrious Member
Joined: 22 years ago
Posts: 4097
 

Check your PM



   
ReplyQuote
Barry Turano
(@barryturano)
Famed Member
Joined: 17 years ago
Posts: 2720
Topic starter  

Just got off the phone with LM Barbour of Fin-Addict fabricators in Benson. They can make what I want out of a heavier Starboard. They make hatches and doors. They say for hatches they use a more robust material . I am going to the boat to take some measurements a photos. They will design and make me a hatch that will fit my needs. They seem to be reasonable, we will see what happens.



   
ReplyQuote
Drew Maultsby
(@)
Prominent Member
Joined: 17 years ago
Posts: 806
 

Best option. I was trying to recall their name last night, but it wasn't registering.
edit: Check to see if the area is close to flat.



   
ReplyQuote
Duane Davenport
(@alltydup)
Trusted Member
Joined: 15 years ago
Posts: 61
 

Sent you a PM Barry, but there is a company here in Wilm that does all kinds of work with Starboard. i think they have the ability to weld it also.
Located of River Rd close to Port City Java's Main office.

Saltwater Woodworking
119 Bryan Rd.
Wilm
910-352 7881



   
ReplyQuote
Drew Maultsby
(@)
Prominent Member
Joined: 17 years ago
Posts: 806
 

Good luck with your project. I put pulpits, rollers and windlasses on my last 3 boats, Gotta have it when you hit 65, and the wife is first mate. I kept the white GW hatch intact, in case I screwed it up too badly.25percent_size_116.jpg25percent_ll_730.jpg24dollar_lll_169.jpg25percent_iv_235.jpgfb89705ae6d743bf1e848c206e16a1d7_727_960.jpg



   
ReplyQuote
Barry Turano
(@barryturano)
Famed Member
Joined: 17 years ago
Posts: 2720
Topic starter  

Sent you a PM Barry, but there is a company here in Wilm that does all kinds of work with Starboard. i think they have the ability to weld it also.
Located of River Rd close to Port City Java's Main office.

Saltwater Woodworking
119 Bryan Rd.
Wilm
910-352 7881

Got your message. Went there Joel was not in. Spoke to one of the guys there I'm waiting for Joel to get back to me. Thanks for the lead.



   
ReplyQuote
Barry Turano
(@barryturano)
Famed Member
Joined: 17 years ago
Posts: 2720
Topic starter  

I spoke with Fin-addict in Benson. Here is a drawing of what I want to have fabricated. Seems fairly simple. Looking at 3/4 to 1" Starboard. It will be a small area. No one will be walking on it so I think it should work.scan_516.pdf



   
ReplyQuote
Page 1 / 2
Share: