SWC Forums
Pull up a chair...let's talk fishing.
Looking on how they ride, wet or dry. Reviews on the 2005 E-tech 225 problems, fuel economy, maintenance. Looking at purchasing one so any help would be greatly helpful thanks.
Don't know anything about your boat choice.
Motor
E-tech is a strong motor, probably the strongest you can find in the newer motors. Good on gas but not quite as good as the new four strokes. The 2nd biggest drawback for the BRP 2 strokes is the oil use. I have used many gallons over the last few years and oil ain't cheap, especially the XD100 that you will use with that motor. The biggest drawback to these motors is service. I have heard good things about Yopp Brothers in Sneads Ferry but have never used them. Your service choices are very limited in NC on certified motor service. If you feel good about the closest dealer, then no worries. Its not like a yammie or zuke or even mercury engine where you have lots of choices for mechanics. I used Bobby's mobile marine service for my last boat with a yammie and he did a great job. He will not touch my evinrude motors and I have had a hard time finding a good mechanic for these motors down near Holden. Personally, I would not buy another boat with Evinrude motors unless there were several service choices available near me. Just my opinion. Good motors but the cost of oil and lack of service choices would make me think twice about purchasing.
Thanks for the info. That helps alot. I do think my local service center service this motor do to they are the ones with the boat for sale and state they have the service records.
SeaHawks are sturdy, heavy built 3 piece hulls.
I would look at buying the rig for no more than
hull and trailer value only.
They are a no frills sturdy platform, but they ride that way as well. 18 degrees of deadrise and North Carolina offshore fishing don't mix well together.
There are lots of boats being sold as Saltwater Boats
with same deadrise than this C Hawk,
example here...
http://seahuntboats.com/new25/boats/tritons/triton-225
Folks seem to accept 18 degree boats more now than in the past, go figure.
They are a no frills sturdy platform, but they ride that way as well. 18 degrees of deadrise and North Carolina offshore fishing don't mix well together.
I know you have been on more offshore boats than I have. What is your most ideal dead rise, or is it dependent on boat length in you opinion?
How old is the hull? The older c hawks were built to handle 2 stroke motors and not 4 strokes. The transoms can't handle the weight of newer 4 stroke motors. Overall c hawk 235cc is a great boat in my opinion, a good friend of mine has one.
1999 hull
How old is the hull? The older c hawks were built to handle 2 stroke motors and not 4 strokes. The transoms can't handle the weight of newer 4 stroke motors. Overall c hawk 235cc is a great boat in my opinion, a good friend of mine has one.
Etec is a two stroke.
I wouldn't worry about the dead rise, it's all about the entry and I believe the C hawks are like a lot of NC boats and have a variable bottom. It won't be a speed demon but run correctly (read not WOT all the time) it will handle anything. C hawks are in the Parker and maycraft vein of solid, no frills work horse boats. You will need to check the transom and stringers though since I believe they are wood encapsulated in fiberglass and you can never tell if a previous owner drilled through and didn't properly seal them back up.
Don't know anything about your boat choice.
Motor
E-tech is a strong motor, probably the strongest you can find in the newer motors. Good on gas but not quite as good as the new four strokes. The 2nd biggest drawback for the BRP 2 strokes is the oil use. I have used many gallons over the last few years and oil ain't cheap, especially the XD100 that you will use with that motor. The biggest drawback to these motors is service. I have heard good things about Yopp Brothers in Sneads Ferry but have never used them. Your service choices are very limited in NC on certified motor service. If you feel good about the closest dealer, then no worries. Its not like a yammie or zuke or even mercury engine where you have lots of choices for mechanics. I used Bobby's mobile marine service for my last boat with a yammie and he did a great job. He will not touch my evinrude motors and I have had a hard time finding a good mechanic for these motors down near Holden. Personally, I would not buy another boat with Evinrude motors unless there were several service choices available near me. Just my opinion. Good motors but the cost of oil and lack of service choices would make me think twice about purchasing.
Well I have had just the opposite experience with my 130 hp E-Tec on my 19' Sea Pro. I get about 30% better gas mileage than my neighbor's 115hp four stroke on his 19' boat. As for oil use the cost of my XD100 oil use is a lot less than his oil changes and filters over the last year. BUT the best thing I like about the E-Tec is the 300 hours or 3 years between service intervals... I would buy another E-Tec without hesitation.
As for service have never had to have any work done on my E-Tec which has 445 hours on it other than lower unit oil changes, and the 300 hour service. But I know of at least four authorized service centers within an easy drive of Morehead City.
As for service have never had to have any work done on my E-Tec which has 445 hours on it other than lower unit oil changes, and the 300 hour service. But I know of at least four authorized service centers within an easy drive of Morehead City.
Many more service centers in Northern part of the state. We are planning on buying up in the AB or EI in the next few years and I will be happy to have service closer. If you look at same boat (builder, hull) with Etech vs a modern 4 stroke (depends on the mfg of 4 stroke), at cruise the 4 stroke gets a little better mileage. The rudes are STRONG motors, lighter, and more torque. I am not bashing etech or evinrude. Just trying to give answers to think about before buying a boat. The oil is damn expensive compared to other TW3C brands.