SWC Forums
Pull up a chair...let's talk fishing.
Got a new Garmin 8612XSV waiting on me at home!!! I absolutely can't wait to get this thing in and tried out.
A few pics. Have a trip all next week so will be at least by then before it goes in. The wait is going to kill me.
I know your pain. Couple years ago when they discontinued the 8212 I picked up 2 in the liquidation sale, it was over 6 months before I was finally able to get them hooked up and use them.
That's a sweet unit. I'm interested to see how they incorporated the Navionics charts into their existing charts. How much Navionics is actually going to be on there.
That's a sweet unit. I'm interested to see how they incorporated the Navionics charts into their existing charts. How much Navionics is actually going to be on there.
I’m not sure but from what I’ve seen from another the charts a a lot more in line with what’s actually there than before.
I just tried to install over the weekend and found out my 4210 footprint is way bigger than I really thought and have to have something the help fill in the gap so install is going to be longer than anticipated.
I did power the unit on though and loaded a few waypoints! It’s pretty sweet and hardly any lag in moving around.

Thats a lot of numbers.Very interested where you got the "Hunter Hole" from
Thats a lot of numbers.Very interested where you got the "Hunter Hole" from
Lucky enough to be blessed.
That's a sweet unit. I'm interested to see how they incorporated the Navionics charts into their existing charts. How much Navionics is actually going to be on there.
I forgot about this thread on THT until I ran across it again. It gives a view of the 7610 and 8610. You can see the differences there
https://www.thehulltruth.com/marine-electronics-forum/983983-garmin-8610xsv-real-world-review.html
Thats a lot of numbers.Very interested where you got the "Hunter Hole" from
Also, it could be the same one listed on this site but not sure.
https://chasintailsoutdoors.com/gps-numbers.php
That's a sweet unit. I'm interested to see how they incorporated the Navionics charts into their existing charts. How much Navionics is actually going to be on there.
I’m not sure but from what I’ve seen from another the charts a a lot more in line with what’s actually there than before.
I just tried to install over the weekend and found out my 4210 footprint is way bigger than I really thought and have to have something the help fill in the gap so install is going to be longer than anticipated.
I did power the unit on though and loaded a few waypoints! It’s pretty sweet and hardly any lag in moving around.
Wow. My 7612 dropped right into the space the 4210 left.
That's a sweet unit. I'm interested to see how they incorporated the Navionics charts into their existing charts. How much Navionics is actually going to be on there.
I’m not sure but from what I’ve seen from another the charts a a lot more in line with what’s actually there than before.
I just tried to install over the weekend and found out my 4210 footprint is way bigger than I really thought and have to have something the help fill in the gap so install is going to be longer than anticipated.
I did power the unit on though and loaded a few waypoints! It’s pretty sweet and hardly any lag in moving around.
Wow. My 7612 dropped right into the space the 4210 left.
Mine too. I actually had to sand about 1/16" off the bottom.
So the 8600 units moved the sd slot to the rear so that extra space all around the unit is gone. I looked at the cutout sheets and thought I’d be close but didn’t know it would be that much off. My neighbor compared it to his 7612 and you can tell they took a good bit off the side where the sd slot was. Not a huge biggie but getting a company to get back with me on a small piece of black acrylic job has been a challenge.
Hey Will. Did you try to call Sea Hunt and ask them for a piece of acrylic? It seems the new GF 25 console is the same as ours.
Hey Will. Did you try to call Sea Hunt and ask them for a piece of acrylic? It seems the new GF 25 console is the same as ours.
Yup. Called yesterday and left a message with parts. Haven’t heard back on that one. Have put in a request to a few but no word back except on place wanting almost $200 for a 13.5”x9” picece cut. Still waiting.
Roger that. I hope you can get one pre-fabbed by Sea hunt to save you some time.

