SWC Forums
Pull up a chair...let's talk fishing.
I had listed my problem in my offshore report but i will post it in here so that it does t clog that forum up.
Background- 1999 Suzuki Dt140's
Port motor has run fine in the past 10 trips that i have put it in no issues at all. on this last trip after idling to the channel and trying to come up on plane it seems as if the prop would break free and not catch any water after 3000-3500 rpms. it would run and once it hit that point it seems that it would shift in to neutral and would not catch again until it went back down to lower rpms. ive been told that it might be the prop clutch or possibly spun the prop. is there any way to test to find out what it is. im trying not to break the bank on this one and do as much of the work myself that i can
Starboard motor-
on the trip before last on the way back in it started to act like it was starved on fuel and revs began dropping then would pick back up again and it would repeat over and over. while trolling it stalled out 1 time then fired right back up again and ran for another hour. the boat was running for about 6 hrs before i had any issue. on the last trip it did the same thing. we ran out and fished from 6-1230 before there was any issue it started to sputter while motoring back in as if it was starved on fuel. when flushing the motors at home it would only stay at idle for about a minute or 2 before it would stall out. I bought some seafoam to run through the outboards but have never used it on a outboard before how do you guys use it? do you mix it with a seperate tank at about 50/50 mix and run it through there or what. Thanks in advance for the help.
Cory
Ok I have found the fuel issue at the thorotle body. It is constantly spitting fuel spitting out of it. if i pump the bulb it spits that would be no regulation in there right? I would have to think that the diaphram is not stopping excess fuel. am I way off on this or what. Here is a short video of what it is doing
I use to have the same outboards and pulled my hair out on a daily basis. Brownspoint.com has complete drawings for any suzuki outboard . This should help you to see where the problem is but it sounds like a ruptured diaphram however I've had old merc's and they did the same thing but ran fine. One problem I ran into was that there is a small inline filter inside one of the hoses that should be changed or at least cleaned. Clean fuel is a must also for that motor so maybe a yamaha 10 micron fuel/water seperator . Sierra makes one also. You can pm me if you want . I'm not an expert but I had that motor apart so many times it made my head spin.
I changed the seperators last week and waiting for the part stores to open I appreciate the help ill send you a pm if I need help pulling it apart.
Top looks fine. Lower not as clear but looks like the rubber hub is a mess.
pulled the props big difference between the two just to confirm does this prop appear to be spun?
Yes sir. I had the same problem and had to run 5 miles basically at idle to get back to the ramp. Pull that prop and have a new coupling installed, maybe $100 and you'll be fine.
I'd say take it in to the prop shop.
prop shop will punch that hub and set a new one in and you will be fine!
MOST-DEF the issue with the PROP on that motor!!!
*I would NOT run the other motor with fuel pouring out like that until you get her fixed!!! BIG FIRE / Explosion going to happen if you do!
Good Luck!
well i found the issue with the fuel problem now the problem is finding replacement part for it. it seems that i can not buy the smaller diphrams that are inside the houseing only the large ones. does anyone know if you can find them somewhere other than having to buy a whole new fuel pump for a $.50 piece. I took some pictures of the blown out piece and where it came from. any help would be great

Well problem solved on the fuel issue motor it wasn't the diaphragm but that was the cause. The piece that belongs where that hole is went down the fuel line and got clogged in the needle for the vapor seperator tank and it would not shut off when it was full shooting fuel out of the vapor hole. Now to get the bearing pressed in and it will be fishing this weekend hopefully
Great News!!!!!! Good Luck this weekend!


