SWC Forums
Pull up a chair...let's talk fishing.
Ok ya'll, I need some advise and direction. I've got a 96 model DF 40 Suzuki on my 16ft jon boat. I'm running a 10in 14 pitch prop and I'm running out of rpms at maybe 3/4 throttle and only making around 30 mph. I don't have a tac, but I can hear the limiter coming in. Also blowing out in the turns and caveating bad. I have looked and looked for a way to go to a bigger prop, cant get any love tho. My cavitation plate is set level with the bottom of the hull to. Just can't seem to figure it out . Any help would be a blessing. Thank guys. :hail:
Ok ya'll, I need some advise and direction. I've got a 96 model DF 40 Suzuki on my 16ft jon boat. I'm running a 10in 14 pitch prop and I'm running out of rpms at maybe 3/4 throttle and only making around 30 mph. I don't have a tac, but I can hear the limiter coming in. Also blowing out in the turns and caveating bad. I have looked and looked for a way to go to a bigger prop, cant get any love tho. My cavitation plate is set level with the bottom of the hull to. Just can't seem to figure it out . Any help would be a blessing. Thank guys. :hail:
Only 30 mph?? That's moving pretty good in a Jon boat!! Obviously the diameter of the prop can only be so large or you hit the cavitation plate, so you need more pitch to bring your WOT RPMs down, but it may be hard to find on a 10" prop. Also, if the prop is worn, you may not be pushing as much water, and subsequently making higher RPMs. If it were me, I'd take a friend for added weight, or just slow down and save some gas.
Does the engine have power trim? You could have it trimmed too far up for turning at speed.
If the rev limiter kicks in before full throttle that usually means you need larger prop or more pitch or a combination of both.
When you say you cant figure out a way for a bigger prop what do you mean ?
Are you sure its a DF40 1996 ? I cant seem to find that model that year. There are several props available for DF40s in larger diameter and more pitch but they start at 1999
1.) For a minimal price you can add a digital tach to the motor. I added one to my Nissan when I was looking at prop selection. Check on-line.
2.) Did you add this motor? Is it a short shaft and maybe you need a long shaft?
3.) Like someone else suggested, is it up too high.
Nonetheless is you have no cavitation and the motor limits out you need more of something. Check on line to some of the prop stores , some have selection guides. I know that the guy at Proptech helps a lot of people. Advice is free I hear.
I have tried to find a larger prop , both in diameter and pitch . Sent and email to Protech with what I have as far as boat and weight. No answer back. I have plenty of room between the prop shaft and cavitation plate to go to go larger, just cant find in aluminum , cant wekll afford to buy severl ss props to test.... lol. If I could I would be running off with you guys...lol. Just saying. Thanks for the advise on this so far. Thanks a lot guys.
I have tried to find a larger prop , both in diameter and pitch . Sent and email to Protech with what I have as far as boat and weight. No answer back. I have plenty of room between the prop shaft and cavitation plate to go to go larger, just cant find in aluminum , cant wekll afford to buy severl ss props to test.... lol. If I could I would be running off with you guys...lol. Just saying. Thanks for the advise on this so far. Thanks a lot guys.
Stainless Steel is worth every penny in my opinion, especially if you fish the skinny water. I found a great deal on my stainless Honda prop on Amazon. I have one that's 10x10 for when I carry a passenger, and one that's 10x12 for just me in the boat. Got them both for $320.
Dang Jason , That's a good deal. Ill look into that for sure. But I still need to figure what size I can go to . Thank you sir.
Dang Jason , That's a good deal. Ill look into that for sure. But I still need to figure what size I can go to . Thank you sir.
Honda has a prop selection tool on their website. I bet Suzuki might as well. If you get a Suzuki part number and enter it as a search on Amazon, you'll probably have better luck.
Dang Jason , That's a good deal. Ill look into that for sure. But I still need to figure what size I can go to . Thank you sir.
Check this out to find Suzuki prop part numbers:
http://www.suzukimarine.com/~/media/marine/accessories/suzuki%20propellers/propellers_pdf.ashx
I don't see any 10" props for your model, so there is a strong chance you don't have the right diameter for your motor. That'd explain the over-rev'ing.
Not sure where you are at, but there are some dealers that have loaners to try before you buy. I'm pretty sure your issue is an undersized, under-pitched prop.
Doesn't look to me like a 10" prop is even listed for a DF40. Looks to me like you need something close to 11-3/4"
Sometimes it's trial and error, but you should be able to get close with one of the prop selector programs online.
Agree Stainless is the only way to go in saltwater.
Ill check that out Steve . Hadn't thought of that at all. What I need to find is a 11 to a 11 1/4 pitched at maybe a 15 or 17. Ill look around here and see what I can find. Im in Southport . .
Jon boats tend to "slide" really bad in turns and since your already running on top of the water with a flat bottom sliding to hard in a turn can cause cavitation.
To give you a good starting point for the determining how fast you will go with a given pitch you can use this simple formula.
rpm / gear ratio * pitch of prop * 60 (places in mph) / 5280 (feet per mile) / 12 (inches in 1 foot) = speed with a given prop
If you put in your max rpm this will give you the mathematically possible top end speed with zero slip. 5-10% slip is not uncommon, and aluminum deflects more than stainless under a load so it "slips" more. The goal in prop select is to strike the right balance between torque and speed. If you can provide your lower unit gear ratio I will work some hypothetical situations for you to further and better explain this.
http://www.brownspoint.com/store/pc/suzuki/df40.asp?gclid=CMXPlN-bw8gCFVcHkQodQxYKEw
I'd start with the serial number, and figure out what engine I had. Like someone said, I don't see a DF40 in '96.
Thanks Adam and Glacier. I did run the serial number and its a 95 model DF40. Adam , I will try and find the ratio for the lower unit. Thank you for the offer and help.
Alrighty fellers.as able to finally talk to a rep at Power tech and he ran my numbers and all , came up with a prop that will help. Guys , I really appreciate the advise and help. Its a good feelin to know I can get on here and get the help and willingness for advise. Thanks again.