SWC Forums

Pull up a chair...let's talk fishing.

Re-Wiring 25ft Cent...
 
Notifications
Clear all

Re-Wiring 25ft Center Console

20 Posts
13 Users
0 Reactions
56.8 K Views
Steven
(@)
Trusted Member
Joined: 12 years ago
Posts: 46
Topic starter   [#45608]

Anyone in the Morehead City area that re-wires boats and was wondering the price range if anyone else has had it done?



   
Quote
Brad Bowen
(@)
Trusted Member
Joined: 19 years ago
Posts: 46
 

Joe Ward



   
ReplyQuote
Rob Thomas
(@kicker30)
Reputable Member
Joined: 18 years ago
Posts: 286
 

Marine 1 in MHC.



   
ReplyQuote
Jordan
(@)
Estimable Member
Joined: 15 years ago
Posts: 126
 

Second Joe Ward, very reaonsable prices: 252-241-2474



   
ReplyQuote
Tim elrod
(@)
Noble Member
Joined: 18 years ago
Posts: 1002
 

Total rewire? Probably $3500-4000+

I have done quite a few boats for myself and can tell you nothing is cheap about it.



   
ReplyQuote
Steven
(@)
Trusted Member
Joined: 12 years ago
Posts: 46
Topic starter  

Thanks for the info



   
ReplyQuote
Larry Rowland
(@lwr37)
Famed Member
Joined: 16 years ago
Posts: 2552
 

Do it yourself! I just rewired my 26' Sea Chaser. I reused the switches but installed new wire and fuse panels. I had a buddy help me pull the new wire through the T-top tubes. I also ran conduit from the console to the transom. For the bilge pumps I used 14/3 wire. For all of the livewell pumps I used 16/2. I also used 16/2 for all of the LED lights. Each light and pump is wired on its on switch so it is as fail safe as possible. I used waterproof heat shrink connectors and then put a second layer of shrink tubing over them. It took me 3 1/2 days to do it and I enjoyed it. The upside is I know how every wire is run and the quality of work. Lighthouse Marine and Trailer Supply has everything you need. Good luck...



   
ReplyQuote
Barry Carter
(@mtrmadman)
Reputable Member
Joined: 22 years ago
Posts: 294
 

Tim and Larry
Did you use tin coated copper or just regular wire. Have a lot to rewire. My boat needs it and my controls and engine 454 I/O volvo
Thanks
Barry



   
ReplyQuote
Tim elrod
(@)
Noble Member
Joined: 18 years ago
Posts: 1002
 

I have always used Anchor Brand Marine grade tinned copper.



   
ReplyQuote
Larry Rowland
(@lwr37)
Famed Member
Joined: 16 years ago
Posts: 2552
 

Tim and Larry
Did you use tin coated copper or just regular wire. Have a lot to rewire. My boat needs it and my controls and engine 454 I/O volvo
Thanks
Barry

I used Ancor marine tinned wire. Do not use regular wire. I probably spent around $600 but I replaced one bilge pump, one float switch and one switch. I used about 200' of 16/2 and 60' of 14/3.

http://www.ancorproducts.com/en/products/wire-and-cable/multi-conductor



   
ReplyQuote
David Lucas
(@)
Noble Member
Joined: 19 years ago
Posts: 1100
 

Joe Ward did mine about 3 years ago. Fantastic Job.



   
ReplyQuote
JOHNNY CARPENTER
(@)
Noble Member
Joined: 14 years ago
Posts: 1169
 

If you have the time, do it yourself like Larry said. Do you need gauges, ignition, and engine related things rewired or just lights, gps, depth finders and accessories? If the latter, should be easy and you can learn a lot and know exactly what you have and where it goes. But, if you don't feel comfortable doing it yourself and have the cash, some of these guys mentioned are real artists and will do a jam up job.



   
ReplyQuote
Barry Carter
(@mtrmadman)
Reputable Member
Joined: 22 years ago
Posts: 294
 

I need it all my wire casing just crumble when you roll it between 2 fingers. I have to rewire all the sensors for EFI engine plus the things like pumps trim tabs electronics and all so I have a lot to learn.
Thanks Barry



   
ReplyQuote
Larry Rowland
(@lwr37)
Famed Member
Joined: 16 years ago
Posts: 2552
 

I need it all my wire casing just crumble when you roll it between 2 fingers. I have to rewire all the sensors for EFI engine plus the things like pumps trim tabs electronics and all so I have a lot to learn.
Thanks Barry

Pumps, trim tabs, electronics and such are pretty easy. It is time consuming but if you enjoy hands on projects it will save you a bundle. Engines I know nothing about but I suspect if you get a good manual that will be pretty simple too. Draw you a nice diagram before you start and get to it!



   
ReplyQuote
Dave Arnold
(@)
Noble Member
Joined: 19 years ago
Posts: 842
 

The question was how much and no one has answered!!!!



   
ReplyQuote
Page 1 / 2
Share: