SWC Forums

Pull up a chair...let's talk fishing.

Taking on Water.......
 
Notifications
Clear all

Taking on Water........

35 Posts
27 Users
0 Reactions
66.6 K Views
Jeff Schmucker
(@rustyone)
Noble Member
Joined: 16 years ago
Posts: 951
 

On the trailer try to fill the hull with hose water, see if any comes out.

this gets my vote! makes sense if it can get in, it should come out too.
good luck john!

Obviously, support the trailer frame with lots of blocking. The tires won't handle much water weight. Don't ask how I know ๐Ÿ™„



   
ReplyQuote
john Smith
(@)
Noble Member
Joined: 18 years ago
Posts: 1776
 

[Obviously, support the trailer frame with lots of blocking. The tires won't handle much water weight. Don't ask how I know ๐Ÿ™„

Not to mention flooding batteries, switches,
wiring connections, fuel tank connections,
trim tab pumps, wash down and livewell pumps etc.



   
ReplyQuote
Grouper Sandwich
(@)
Noble Member
Joined: 15 years ago
Posts: 1213
 

[Obviously, support the trailer frame with lots of blocking. The tires won't handle much water weight. Don't ask how I know ๐Ÿ™„

Not to mention flooding batteries, switches,
wiring connections, fuel tank connections,
trim tab pumps, wash down and livewell pumps etc.

thanks for the obvious common sense aspect FF, but I'm sure Capt. midnight knows when to stop the water, he's been around the block a time or two :wtg:



   
ReplyQuote
Johnny Byrd
(@)
Estimable Member
Joined: 23 years ago
Posts: 195
 

Don't know what you are running now John but a friend of mine had an inboard/outboard which had leaking freezeplugs.



   
ReplyQuote
Kevin Daniels
(@)
Estimable Member
Joined: 14 years ago
Posts: 173
 

I would try the sea cock and hoses first. If that it the problem, filling the hull with water is unlikely to show there, as the hoses themselves need to be filled. Only thing filling the hull will show is hull fractures or thru hulls that are not sealed properly. My bet is the boat was being run with the sea cock open and the increase in speed increased the water intake just as it is designed with the exception the water is going in the bilge. As far as the bumper mold, it should only be effected at higher speed or in the process of speeding up as when the boat is sitting level (trolling or drifting) there is no applied pressure to force water under the seam and on plan the transom should be higher enough to clear the molding above the water. Don't rule out anything but I believe it has to do with a sea cock and hose as while you were going slow the intake was slow. As you speed up so does the water intake. Good luck with it and keep us posted



   
ReplyQuote
Mark Gorges
(@captaingorges)
Noble Member
Joined: 20 years ago
Posts: 1581
 

I sincerely doubt John's batteries, switches or trim tab pumps are in his bilge and his fuel connections, wiring and pumps are waterproof (or should be). Its a bilge, in a boat; its made to get water in it without the boat self-destructing.

If it is a leaky sea-cock, loose fitting, etc. I would think 6 inches of water in the boat would start showing leaks.



   
ReplyQuote
Victor Gulley
(@)
Noble Member
Joined: 17 years ago
Posts: 872
 

John; I had this very same problem a couple of years ago and it 'bout drove me crazy. Then it hit me the key was water coming in at anchor - has to be a below water line thru hull.

Backed the boat down the ramp with just the drain plug below water, nothing, then the bait well drains-nothing then the bait well pickup - nothing. backed the boat off the trailer and docked it, parked the truck and by the time I got to the boat the bilge pump was running. Took me a few days to remember water has a hard time running uphill - boat on trailer on the ramp - DUD..

Turned out to be the screw in drain plug and it's thru hull fitting. Changed both the fitting and screw in plug - no more problem. Just be sure. to use enough 5200 on the thru-hull.
Good luck and hope you get it solved.



   
ReplyQuote
zigzag
(@)
Noble Member
Joined: 22 years ago
Posts: 1863
 

so what kind of boat and engine setup are we talking about?



   
ReplyQuote
Jeremy Brown
(@weekendhooker)
Noble Member
Joined: 15 years ago
Posts: 1552
 

My wash-down hose came loose from the fitting and since it was tied into the high speed pick-up on the baitwell I was pumping water into the bilge while running with the baitwell ON.

I agree that you need to turn OFF all of your 1/4 turn valves then run the boat. Open one and run the boat...then another...then another until you find the source.

If water is getting into the boat as soon as you back her off the trailer with no running I would try the garden hose method of filling the hull with water and looking for any leaks.

Good Luck!



   
ReplyQuote
John
 John
(@)
Famed Member
Joined: 20 years ago
Posts: 3801
Topic starter  

Wow, Thanks for all the tips guys!!!!

I have tried a lot of them, but some I had not thought about.

Going to let these storms get out of here and put her in the water and, using a lot of this info, see if I can find where it's coming from.

Will report back when I find it in case someone else goes through this.

Thanks again for the help,
John



   
ReplyQuote
Vaughn Ford
(@)
Prominent Member
Joined: 19 years ago
Posts: 637
 

I had a cracked out feed tube on my Livewell in my last boat. Under the leaning post and didn't find it until doing some work on my gas tank. Good luck tracking it down



   
ReplyQuote
nathan justice
(@)
Estimable Member
Joined: 14 years ago
Posts: 198
 

My money is on the baitwell. I had a similar issue with a seacock valve being closed on my baitwell drain when I took delivery of the boat. When the baitwell level reached the overflow drain it had no where to go and kept filling until leaking over the top which went into the hull. I noticed my bilge was running randomly when I was offshore. Opened the seacock on the drain and problem solved.
Good luck! Damn boats! Love em and hate em!



   
ReplyQuote
Scott
(@scottk)
Noble Member
Joined: 20 years ago
Posts: 1338
 

John - Know anyone with a plumbers snake camera you could borrow? Have a helper poke around with that. Do you know if you get more coming in while stationary or underway?
More underway would indicate a high speed pickup through hull to me.



   
ReplyQuote
r f burke steele 111
(@goosin)
Active Member
Joined: 17 years ago
Posts: 15
 

ran into a similiar situation...tried many of the things discussed...ended up being a stress crack that was not that obvious to the eye...the only time water would enter was traveling in offshore conditions....not while trolling or running inshore. Good luck with the fix.



   
ReplyQuote
John
 John
(@)
Famed Member
Joined: 20 years ago
Posts: 3801
Topic starter  

Fixed!!!!!! 2-6" o-ring seals on access hatches in the splashwell had worn out.

These are all good tips. Someone ought to keep them incase someone else is looking for a leak.

Amazing how much water can come in such a small opening!!!!

Thanks again



   
ReplyQuote
Page 2 / 3
Share: