SWC Forums
Pull up a chair...let's talk fishing.
I know this will probably vary due to differences in boats and fishing areas, but what do yall consider essential in your toolbox on the boat? List type of boat (ib, on, ib/ob) and type of fishing you do also (inshore, nearshore, offshore).
A prop wrench or a crescent wrench big enough to remove and replace a spun prop while on the water. I carry a plastic prop wrench on my 19' CC with an outboard. Of course the wrench doesn't help unless you're carrying a spare prop too. On my last inboard boat I carried a mask, snorkel and fins too.
Wire snips, electrical connectors, and fuses. 90% of what we use on boats needs electricity.
In addition to everything that's been mentioned, a cheap socket set and a couple screwdrivers will go a long way. All of this stuff will fit inside a small rubbermaid container that can stay inside the console.
4 way screwdriver, Lg and mall crescents, channelocks, vice grips, elect crimped/stripper connectors, elect tape, sm. brass wire brush, hammer, stubby wrenches, sm. pieces of sandpaper, zip tie assortment. Keep it in a small Flambeau rust-preventing tool box with VCI emitters.
After Capt. Troy's misfortunes with shaft seals, I'm sill looking for a 2 ft aluminum pipe wrench!
Sea Tow......only tool you need. ........ ICM
24 Albie-inboard------I'am with ICM though I do carry a full tool box. I do have spar props but with counter-rotating props --two different sized prop nuts for each, no way am I getting out of boat trying to change both. Relay to SEATOW for me.
4 way screwdriver, Lg and mall crescents, channelocks, vice grips, elect crimped/stripper connectors, elect tape, sm. brass wire brush, hammer, stubby wrenches, sm. pieces of sandpaper, zip tie assortment. Keep it in a small Flambeau rust-preventing tool box with VCI emitters.
After Capt. Troy's misfortunes with shaft seals, I'm sill looking for a 2 ft aluminum pipe wrench!
AND.....emergency bilge pump with 25' of cord, aligator clips, 20' of hose!!! :lmao: :lmao: :lmao:
Socket wrench set, a collection of box wrenches, a couple of adjustable wrenches in different sizes, pliers both channel locks and a big set and little, filter wrench, vice grips, needle nose as I am always needing them, duct tape, electrical tape, screw drivers of assorted types, wire strippers- crimpers, electrical test light and ahm meter, small hammer, WD40 and CRC, and a tube of 5200.
Also have xtra fuel filters, oil filter, a couple of quarts of motor oil, power steering fluid, and a power steering hose. Had one of those jewels burst one time and it was a long ride back with no power steering! two wooden plugs that will fit my through hulls, and a few stainless hose clamps.Almost forgot the dive mask for the brother in law on those early rides out when its a little chilly to dive over and remove the wayward black fish pot line.
Thats about it I think. You never know what you will be hit with and I like to keep fishing if at all possible and make it home in the same day.
Battery Pack to jump start the motors. Pull cord to pull start the motors. Prop Wrench, spare hub, spare prop, spare trim tilt relays.
Assorted fuses. Socket set, fuel filter wrench, spare fuel filter.
I carry everything I can.
All sizes of screw drivers, wrenches, sockets, wires, connectors, screws, nuts, bolts, spare parts, vice grips, pipe wrenches, pry bar. Basically any tool I could use on land I carry on the water except a prop puller. With an inboard, my prop is not getting changed unless she is on the hard.
I don't want to have to rely on sea tow or anyone else. If I can fix it, I will so I carry all the tools and parts I might need.
I carry everything I can.
All sizes of screw drivers, wrenches, sockets, wires, connectors, screws, nuts, bolts, spare parts, vice grips, pipe wrenches, pry bar. Basically any tool I could use on land I carry on the water except a prop puller. With an inboard, my prop is not getting changed unless she is on the hard.
I don't want to have to rely on sea tow or anyone else. If I can fix it, I will so I carry all the tools and parts I might need.
you sound just like a friend of mine that I fish with. He could improve his fuel economy if it wasn't for the 1000 lbs of tools he has onboard
I have a Volvo penta with the sx drive. Over the winter I've been doing maintenance and repairs and have found out I can do most repairs with a 8 pc combo wrench set that I picked up at harbor freight for 8 bucks. A 6n1 screwdriver, wire tools (crimpers/stripper) a 12" pair of channel locks, and a #50 torx bit. Plus a spark plug wrench and electrical tape.
I have had all the bolt ons, alternator, ps pump, water recirc pump, raw water pump, fuel pump, plus the heads and intake manifold removed. The only thing I used a socket for was the plugs. I have tons of sockets and sockets would have made it faster but I don't want all that weight on the boat. That being said I just weighed the bag and its a whopping 6.3 lbs. And from exp. I know I can make almost any repair at sea if I have the parts.
As far as parts, I have an extra fuel pump, fuel filter, belts, spark plugs, a couple feet of wire and hose in diff sizes, assorted clamps and barb fittings. And probably the most important a hand full of wedge plugs incase a thru hull breaks.
I carry a lot of tools as well and a few years ago it saved my butt when both flywheels came loose 35 miles offshore, now I carry a few more and a cordless impact drill
everything said plus Rescue Tape and Velcro strapping.