SWC Forums

Pull up a chair...let's talk fishing.

Notifications
Clear all

Pulling high speed wahoo lures

15 Posts
13 Users
0 Reactions
1,327 Views
David Bergemann
(@)
Estimable Member
Joined: 15 years ago
Posts: 110
Topic starter   [#30220]

Looking to do some high speed trolling for wahoo, 18 to 20 knots. Question; Can I get by with a Penn 30 wide spooled with 50 lb mono (largest outfits I have), and what is the best setup, 32oz trolling weight, just a heavy lure, or both? Just thinking that as I move from place to place might as well be pulling something! Thanks guys.



   
Quote
(@capt_john_c)
Member Moderator
Joined: 19 years ago
Posts: 1128
 

You are gonna struggle with using a 30. 50 I think would be a minimum option. I usually use 80 when going that speed.



   
ReplyQuote
reelaxin
(@)
Estimable Member
Joined: 23 years ago
Posts: 111
 

With the full size islander / squid baits and that size weight you’re going to better off borrowing a couple 50's or 80’s and don’t forget to add a shock leader between the weight and lure, we use at least 30' of 200# mono. It is there for the stretch on hookup.
Check for backing plates on your rod holders, the stress of a big Wahoo hit against the lock down drag you will be using to keep the main line from creeping out is unbelievable.
Back that drag off as soon as you’re hooked up or the main line can bust easily.
You only need 2 setups trolling at that speed.
We use only about 4' of HEAVY wire on the lure. You don’t want the lure running up the line past the hooked fish or it may get bit off by another fish and you lose everything.
You will have to pull that weight and shock leader in hand over hand. I set a 5 gal bucket in the pit at each setup to drop the weight into and then feed the shock leader ad you pull it in, that way if you must drop the leader the line and weight are not flinging around inside the boat, they just feed back over the side - learned that the hard way. If a big fish runs and you have to drop the leader watch out for that weight, it is going to come out of that bucket and over the side at warp speed. An experienced wireman should be on the leader.
It’s a blast if you can get into them- we picked up 2 citation fish and a bunch of 20 to 30 pounders last time we gave it a go. It will get your attention when a 70lb fish doing 30 knots one direction hits a bait that is doing 15 knots the other way.
It’s about time to make a run for them.



   
ReplyQuote
bryan
(@)
Estimable Member
Joined: 16 years ago
Posts: 104
 

Could you get by with a Penn 30W spooled with 50 pound mono? My gut feeling is yes, you will put wahoos in the boat with that set up. Is it the ideal tool for the job? No, but until you get some 50s or 80s, what the heck, give it a go. I will warn you, at 20 kts, when a big wahoo hits it will be a train wreck, you best be on your game.
And the second question, at that speed, yes you will need a trolling lead. I would also consider building a step-up leader to the lead, and then 30 to 50 feet of atleast 200 lb mono leader to the cable on your lure. We pitch a couple of them out when the situation calls for it... and I agree... it is a blast when it all goes down.



   
ReplyQuote
William McCann
(@werewolf0711)
Famed Member
Joined: 15 years ago
Posts: 3133
 

If 30w was my biggest reel, I would personally consider putting 80lb braid on it topped with about 50-100 yards of 80-100lb mono on top of it for what you are asking and then the 200lb leader with the wire and lure and some lead. But, if you not looking into changing line, then you should get by with what you have. Just be careful because there will be tons of tension on that line, rod, and drag on the reel. And the drag is no joke, as mentioned make sure you back off some as soon as the fish hits



   
ReplyQuote
Dan Rahe
(@)
Reputable Member
Joined: 21 years ago
Posts: 218
 

I do it all the time with a penn 30w, a Shimano 30w and a shimano 50w. The penn is loaded with 100# braid, the 30w shimano is filled with 50# mono over braid and the 50w is filled with 130# braid. You should have no issues. You may wear out the drags faster, but we have never had any sort of mechanical failure with the reels. We use 16 to 24 oz. of weight with a heavy shock leader to the (heavy) lure of your choice. We have found 12 to 14 kts to be the most productive speed. We normally set high speed stuff out when we hit say 130 ft and then switch to baits once we get to the break, or when running between spots. Good luck, it's been productive for us but not something we do for the entire day.



   
ReplyQuote
(@)
Noble Member
Joined: 19 years ago
Posts: 1125
 

ALL I CAN SAY IS KEEP IT SIMPLE....DON'T TRY TO BUILD A BABY GRAND PIANO WHEN A CORNSTALK FLUTE WILL DO THE JOB



   
ReplyQuote
Dan Rahe
(@)
Reputable Member
Joined: 21 years ago
Posts: 218
 

ALL I CAN SAY IS KEEP IT SIMPLE....DON'T TRY TO BUILD A BABY GRAND PIANO WHEN A CORNSTALK FLUTE WILL DO THE JOB

amen....



   
ReplyQuote
David Bergemann
(@)
Estimable Member
Joined: 15 years ago
Posts: 110
Topic starter  

Thanks for the great feedback. I was hoping someone had done it successfully with the 30w. Sounds like you've been able to pull it off wahoowacker. I think I'll try the lighter weights 16 to 24 oz and less speed until I can get hold of some larger outfits. Just trying to avoid broken gear and fish dragging around chunks of lead. Thanks again for the advise.



   
ReplyQuote
Ronald j bailey
(@rjb)
Estimable Member
Joined: 19 years ago
Posts: 112
 

An opinion: I would never pull an in-line lead when High Speed Trolling. Use a lead lure 1-3 #. You can go as fast as you want as long as you keep the lure below the surface. If it starts to pop out of the water you are going to fast. slow it down just a little. Island Tackle has a selection of the heavy lures, but I make my own. Good Luck !



   
ReplyQuote
Rob Orr
(@jrjbfishing)
Reputable Member
Joined: 20 years ago
Posts: 200
 

Its not ideal, but you can most definitely do it with a 30w.

The magic number for us has been 14-18 knots. At that speed, you don't need a trolling lead if you have a 3-5 oz lure. Put it back 150+ yards and hold on!



   
ReplyQuote
HogWild26
(@hogwild26)
Reputable Member
Joined: 20 years ago
Posts: 210
 

I pull a smaller highspeed off my tiagra 30W with 80lb braid. Its a ballyhood. They have several options and doesn't pull much drag with a 16oz weight. I pull an islander with squid skirt and 32oz weight behind the 80W and it pulls much much harder.

Only thing is with 50 mono you may get spooled or lose the fish if you slow down too quick trying to avoid it.

Always be sure to strap in rods, especialy bent butts. My 80W BB took a leap once and it was scary! luckely strapped in!



   
ReplyQuote
chris wright
(@cfarmd)
Reputable Member
Joined: 17 years ago
Posts: 294
 

You can high speed troll without a trolling weight but the weight is designed to lower the trajectory of the lure to help keep the actual lure in the water. Bent butts also make this much easier as they likewise lower the angle of the line to the water I use 2 50wides on bent butts with 24oz trollig weights and 1+lb lures



   
ReplyQuote
Grouper Sandwich
(@)
Noble Member
Joined: 15 years ago
Posts: 1213
 

Its not ideal, but you can most definitely do it with a 30w.

The magic number for us has been 14-18 knots. At that speed, you don't need a trolling lead if you have a 3-5 oz lure. Put it back 150+ yards and hold on!

14-18 knots for me put my boat trying to plane out... once on plan the slowest i can go is about 20Knots

is this too fast or would my ratio be higher at the low speed of 10-12 knots



   
ReplyQuote
wbfish
(@)
Reputable Member
Joined: 20 years ago
Posts: 350
 

I've caught a big bull dolphin going 18 kts while hi speeding and caught a wahoo at 21 kts.



   
ReplyQuote
Share: