SWC Forums

Pull up a chair...let's talk fishing.

Notifications
Clear all

TLD Bearing Removal

17 Posts
8 Users
0 Reactions
386 Views
Scott
(@sctkhouse)
Eminent Member
Joined: 16 years ago
Posts: 18
Topic starter   [#43407]

Not sure this is the correct forum... didn't see a "gear" forum so go easy on me if I'm in the wrong spot.

I've got a TLD 15 I am doing maintenance on and need to replace the ball bearing that is inserted into the side plate. I can't get the old one out. Anyone have a good trick or know of who I should take it to local here in Wilmington/Hampstead?



   
Quote
brent aldridge
(@)
Reputable Member
Joined: 14 years ago
Posts: 200
 

Have u tried youtube? I am sure someone has a video on the most common reel out there!!!



   
ReplyQuote
Scott
(@sctkhouse)
Eminent Member
Joined: 16 years ago
Posts: 18
Topic starter  

Yep, trolled Utube already. First place looked. Bearing is in rough shape and can't seem to get it to break free from the side plate. Picked up the reel this way, figured it would be an easy fix.



   
ReplyQuote
George Stilson
(@gstilson)
Eminent Member
Joined: 13 years ago
Posts: 45
 

The way I get mine out is to stick a pair of needle nose pliers in the hole and spread them so it wedges the bearing and pull it out. If it's corroded in there and is not in good condition you might as well use brute force to get it out. If it's in ok condition spray out with carb cleaner and oil up. Check out alan tani his tutorials are the most detailed.



   
ReplyQuote
Scott
(@sctkhouse)
Eminent Member
Joined: 16 years ago
Posts: 18
Topic starter  

Thanks will try the needle nose pliers. Saw Alan's posts. He has some kind of screw driver with a bent tip. I don't have anything thin enough to get in there it seems.

Bearing is shot, already have a replacement in hand.



   
ReplyQuote
zigzag
(@)
Noble Member
Joined: 22 years ago
Posts: 1863
 

if it is froze up try a tap, it may go thru with just enough pressure to push it out, where are you located?



   
ReplyQuote
Scott
(@sctkhouse)
Eminent Member
Joined: 16 years ago
Posts: 18
Topic starter  

Tried pliers and also I have the tool for removal of retaining rings (like pliers that apply pressure outward instead of inward) with no luck.

Bearing is not frozen. Just bad. Like reeling over crushed marble .

I'm out in Hampstead.



   
ReplyQuote
bjsc21
(@bjsc21)
Reputable Member
Joined: 18 years ago
Posts: 329
 

Try making a tool with a big nail by grinding it down and bending it to make an L shape so you can pull it from the back side. Attach some vice grips to it so you will have something to pull with. I saw a reel repair guy that had made a tool like this just to pull bearings.



   
ReplyQuote
Rich Domanski
(@)
Reputable Member
Joined: 14 years ago
Posts: 256
 

I would soak it with pb blaster.

I had that were tight on my 15's. I have used a copper #12 wire bent with a 90 at the end and snipped to get bearings out.

Two things I will tell you is to use corrosion X on the bearings instead of grease. Only grease the main gears. I also added carbon washers and cal drag grease to mine. Both of these made huge improvements over stock form. I use these primarily for my king set up.



   
ReplyQuote
Scott
(@sctkhouse)
Eminent Member
Joined: 16 years ago
Posts: 18
Topic starter  

Modified nail sounds like a great idea! I'll see what I can do.

In Alan's post he recomended using marine grease on the one bearing in the side plate. Was planning on following his directions.

I also picked up the Penn carbon washer he indicated to use.

Did you swap or reconfigure any other parts when converting to the carbon drag? Have cals grease ready to use on the drag washer.



   
ReplyQuote
George Stilson
(@gstilson)
Eminent Member
Joined: 13 years ago
Posts: 45
 

Modified nail sounds like a great idea! I'll see what I can do.

In Alan's post he recomended using marine grease on the one bearing in the side plate. Was planning on following his directions.

I also picked up the Penn carbon washer he indicated to use.

Did you swap or reconfigure any other parts when converting to the carbon drag? Have cals grease ready to use on the drag washer.

Although Alan is one of the best I don't agree with the usage of grease in a bearing. If smoothness and free spinning is what you want in a reel, don't grease them but if you are ok with it feeling sluggish and want the bearing to last longer use it. Sometimes i may dilute the grease with some compatible oil to make it thinner but i usually just oil with some old reel butter that I have that has thickened up. I don't bother with the marine grease so instead I just use blue penn grease, it seems similar. Cals grease is also always good to have on hand.



   
ReplyQuote
Rich Domanski
(@)
Reputable Member
Joined: 14 years ago
Posts: 256
 

Modified nail sounds like a great idea! I'll see what I can do.

In Alan's post he recomended using marine grease on the one bearing in the side plate. Was planning on following his directions.

I also picked up the Penn carbon washer he indicated to use.

Did you swap or reconfigure any other parts when converting to the carbon drag? Have cals grease ready to use on the drag washer.

I should rephrase the corrosion X statement. I use that on the bearings related to free spool, it makes a huge improvement.

The carbon washers are awesome and a huge improvement over the laughable canvas washers.

Other than those two things that is all I did.



   
ReplyQuote
Scott
(@sctkhouse)
Eminent Member
Joined: 16 years ago
Posts: 18
Topic starter  

Bjsc21, thanks for the nail tip!! Was able to remove the old bearing from the side plate.

Also completed the drag washer swap as well.

All went smooth after the bearing was removed.

Thanks to all for your input and suggestions.

Now on to service my other reels starting with the 25s.



   
ReplyQuote
Con Grant
(@)
Estimable Member
Joined: 17 years ago
Posts: 117
 

If can get a rope through, stick through, tie a knot or two in the rope and pull it out.



   
ReplyQuote
Con Grant
(@)
Estimable Member
Joined: 17 years ago
Posts: 117
 

If can get a rope through, stick through, tie a knot or two in the rope and pull it out.



   
ReplyQuote
Page 1 / 2
Share: