SWC Forums

Pull up a chair...let's talk fishing.

05 Suzuki DF 115 en...
 
Notifications
Clear all

05 Suzuki DF 115 engine problem

9 Posts
6 Users
0 Reactions
30.5 K Views
mark house
(@)
Eminent Member
Joined: 15 years ago
Posts: 26
Topic starter   [#39315]

Last week engine cranks and runs fine but after engine gets warm and when put into neutral engine cut off, easily restarted and could back into slip. Yesterday problem got a lot worse - now when cold starts fine run down the waterway great but after engine gets hot, when put into neutral cuts off and wont start unless i take out of gear and rev, it will start and run at a rev but when i try to put in gear or go to neutral cuts off and wont restart unless i take out of gear and rev, can let sit and get cold will start and run great ?



   
Quote
JOHNNY CARPENTER
(@)
Noble Member
Joined: 14 years ago
Posts: 1169
 

"I just found out that I have EXACTLY the same problem on my 2004 DF140 with 520 hrs. Service by dealer every year. Flushed after each use. I have praised this engine for 6 years, runs great! Had some random stalling problems at idle speed this year. Dealer says it was "choking on fumes".
There is a plug in the port side of the "engine holder". This part is on DF90 thru DF140. The plug is ferrous metal in an aluminum housing that has hot exhaust behind it. It was intended as a potential place for service to install an O2 sensor which they ended up never using. The corrosion is from the inside out. Its not salt corrosion because there's no water there. Its bimetalic corrosion and clearly a defect in material or design. My guess is cheap chinese stainless steel plugs and some get lucky, some don't. Hence, Suzuki has stopped tapping/plugging the hole in newer models. I didn't ask what year. Mines's a 2004.
The dealer said he has seen exact same problem in 3 older engines. One was in a twin configuration with one motor badly corroded so they took the other apart and it was fine.
Estimated cost to repair $1800 ($1018 for parts). Hopefully he doesn't find corrosion in the head or oil pan. "

Not me above but I've heard this is a common problem. Some people just have a good welder to weld a patch on it and it fixes the problem.
Attached Images



   
ReplyQuote
mark house
(@)
Eminent Member
Joined: 15 years ago
Posts: 26
Topic starter  

Thank you so much that makes sense. Didnt see any images attached



   
ReplyQuote
JOHNNY CARPENTER
(@)
Noble Member
Joined: 14 years ago
Posts: 1169
 

Do a search on yahoo.com. You will find many articles on it with images.



   
ReplyQuote
rick
 rick
(@)
Eminent Member
Joined: 19 years ago
Posts: 18
 

I had the same issue on my 2002 df115. Pull off the port side pan on the engine
you should be able to see the plug with an Allen head corroded. I had Robert at
Kings marine in dutch square Wilmington weld a new plug in mine think it cost 50 or 75 bucks. He has done several of these Suzuki with the same issue. I've put around 200 hours on it since, seems to be holding up fine.



   
ReplyQuote
James
(@)
Noble Member
Joined: 20 years ago
Posts: 908
 

Your problem is the IAC valve. Take off the flywheel cover and it is right under it. About 300 new.



   
ReplyQuote
JEFF MORRIS
(@)
Trusted Member
Joined: 17 years ago
Posts: 72
 

I agree on the iac had same problem last year on a 225 but if like mine it was a Mitsubishi part and can get from auto parts dept. for less than 100.



   
ReplyQuote
Marc R Gilson
(@gillie)
Active Member
Joined: 15 years ago
Posts: 15
 

Gore Marine fixed mine.
(910) 763-6066



   
ReplyQuote
James
(@)
Noble Member
Joined: 20 years ago
Posts: 908
 

If your not getting an alarm it's not the engine holder. If you are getting alarm and it goes away when you remove the cover then you have the engine holder issue. Your problem is the IAC.



   
ReplyQuote
Share: