SWC Forums

Pull up a chair...let's talk fishing.

Notifications
Clear all

Deadrise

9 Posts
8 Users
0 Reactions
32.5 K Views
Kevin Welsh
(@)
Trusted Member
Joined: 20 years ago
Posts: 52
Topic starter   [#46238]

I am looking for a 18 to 20 foot CC. I fish a little off shore 10 miles or so and a little inshore with the wife. I've been told to think about the deadrise for the fishing I will be doing and just riding around. What would be the best DR for this type of fishing, riding. Some one told me at least a 17 DR, is this true. Thank you



   
Quote
Barry Turano
(@barryturano)
Famed Member
Joined: 17 years ago
Posts: 2720
 

The more dead rise the better. It will cut through waves and not pound as much (if at all),. The down side is if you are going to anchor or drift off shore they will roll a bit more. My boat has a 24 degree dead rise for to aft. She will cut through any thing. 18 degree dead rise is more than acceptable for a 20' boat.



   
ReplyQuote
Jamie Blue
(@)
Famed Member
Joined: 20 years ago
Posts: 3660
 

Meh dead rise is not the end all. The way boats perform is based on a lot more factors than just deadrise.



   
ReplyQuote
Adam Parchman
(@)
Reputable Member
Joined: 11 years ago
Posts: 193
 

Deadrise is a buzz word these days. The flatter she is at the transom the easier she is to shove and less water she draws. The more v forward the better she will cut. The effective deadrise is where the ride is really felt, where the boat actually contacts the water on plane. Length, width and weight are also very important factors. An 18' boat is a small boat and small changes have big affects thats why 2 of the same boats can ride very different. Since we are talking mold boats the bottom will not be warped like a custom carolina and will most likely cary the transom deadrise farther forward to affect effective deadrise. I would say a transom deadrise of 12-18 degrees would be ideal for an ocean going 18" giving you an effective deadrise of 18-24 if it has an modest entry. A hull design is simply a collection of comprimises. For what you gain in one area you must give in another. Flat is efficent, shallow and stable, v is less efficent, deeper, more listing and better ride in chop.



   
ReplyQuote
john Smith
(@)
Noble Member
Joined: 18 years ago
Posts: 1776
 

Deadrise....the more the better

(measure at the transom)



   
ReplyQuote
Tim elrod
(@)
Noble Member
Joined: 18 years ago
Posts: 1002
 

I have a Pioneer 197SF with a Suzuki DF150 . It has a 57 degree entry, 20 degrees at the transom, and weighs around 4800# loaded to fish. With the tabs down it rides like a much bigger boat and is the best riding sub 21 foot boat you can buy. If it is too rough for me, it's too rough. I get between 4.7-5.4 MPG depending on load and conditions. I normally fish in the 10-40 mile range, but I can also get into skinny water if needed. I draw about 16-18 inches. The company has outstanding factory support and it is a nicer fit and finished boat than the usual SeaHunt, Tidewater, ETC. My boat is 8 years old and still looks new. Resale is excellent. I have been offered recently about what I paid new.

Tim



   
ReplyQuote
John
 John
(@)
Famed Member
Joined: 20 years ago
Posts: 3801
 

Look up Seaswirl Boats and read about deadrise and point of entry and deep Vee and flare.

Mine is a var dedrise with a very deep vee and a lot of flare.

Never had any green water over the bow and she has been in some rough stuff. Very smooth ride in choppy seas.

Good Luck



   
ReplyQuote
zigzag
(@)
Noble Member
Joined: 22 years ago
Posts: 1863
 

these are 2 very good characteristics



   
ReplyQuote
Kevin Welsh
(@)
Trusted Member
Joined: 20 years ago
Posts: 52
Topic starter  

Thank you everybody for your reply. It seems I will look for a deeper V than I was looking at. Very helpful Thanks



   
ReplyQuote
Share: