SWC Forums

Pull up a chair...let's talk fishing.

Deck repair. Fill h...
 
Notifications
Clear all

Deck repair. Fill holes with 5200, resin, or gel coat? HELP!

13 Posts
12 Users
0 Reactions
31.3 K Views
Wesley
(@)
Eminent Member
Joined: 15 years ago
Posts: 12
Topic starter   [#27165]

I recently removed an old T-top off my boat and had a new one built. The pads that were removed left the screw holes. What's the best way to seal these to where I'll never have to worry about water getting below the deck??

It's a Carolina Skiff boat and I have a can of the manufacturer gel coat that goes on the deck. Should I just use that?? What about putting some resin down in the holes? How would I get gel coat OR resin in those small holes anyways? After filling the holes I plan to glue small starboard plates over the areas to cover them up.

I also thought about shooting some 5200 down in them but I'm scared over time they will leak.

ANY help would be greatly appreciated!





   
Quote
Wesley
(@)
Eminent Member
Joined: 15 years ago
Posts: 12
Topic starter  

Or what about thickened epoxy??



   
ReplyQuote
James
(@)
Noble Member
Joined: 20 years ago
Posts: 908
 

Marinetec epoxy, sand, and paint.



   
ReplyQuote
Rich
 Rich
(@squid-row)
Illustrious Member
Joined: 22 years ago
Posts: 4097
 

Marinetec epoxy, sand, and paint.

What he said



   
ReplyQuote
Donnie Johnson
(@redskindon)
Trusted Member
Joined: 19 years ago
Posts: 69
 

Marinetec epoxy, sand, and paint.

What he said

Make sure you get a "fresh" container. I bought one that had been on the shelf for a while. It didn't seem to work up the way some I had used in the past did. Just my .02.



   
ReplyQuote
(@)
Noble Member
Joined: 22 years ago
Posts: 1016
 

I would put regular epoxy thickend with a little collidal silica (cabosil) do not put 5200 it will hold moisture and cause rot. If you use marine tex it will not soak into the wood like epoxy. You can buy a small repair kit of west system at west marine. Fix it right and you will never have to worry about it again. Trust me I am repairing what was not done right the first time on the Carolina time now, after 20 gallons of epoxy I think we are about done. Just my 2 cents.



   
ReplyQuote
(@curmudgeon)
Noble Member
Joined: 21 years ago
Posts: 1317
 

5200 is a great adhesive and a decent sealant. It is NOT a filler ... 😯



   
ReplyQuote
Matt
 Matt
(@)
Famed Member
Joined: 16 years ago
Posts: 2497
 

I like to use that atwood epoxy for things like that. It is sold at walmart in a two part log. Just cut off what you need, mead it for one minute and fill the holes. Good stuff.



   
ReplyQuote
Coastal Pursuit
(@coastal-pursuit)
Trusted Member
Joined: 20 years ago
Posts: 70
 

I would put regular epoxy thickend with a little collidal silica (cabosil) do not put 5200 it will hold moisture and cause rot. If you use marine tex it will not soak into the wood like epoxy. You can buy a small repair kit of west system at west marine. Fix it right and you will never have to worry about it again. Trust me I am repairing what was not done right the first time on the Carolina time now, after 20 gallons of epoxy I think we are about done. Just my 2 cents.

I have to agree with this. You will have to fill the holes twice because it will settle and soak in. This is the way I do my repairs



   
ReplyQuote
Luke D Donat
(@)
Estimable Member
Joined: 18 years ago
Posts: 112
 

Take one size larger drill bit and drill out old caulk/ wet/ old debris. Next chamfer out each hole so the top looks like a cone shape, (this will insure a water tight bond. Next mix some polyester resin, hardener, thin it out with acetone. Pour into the holes. This should allow seepage into the substrate to create a honeycomb effect. Next mix resin, hardener, and cabosil to create a putty just thin enough to drip and fill. Let harden. Top off with gelcoat. This works for me. A bit tedious, but you will never have to worry about it again.

Luke Donat
Donat Marine Solutions
(910) 200-9331
www.donatmarinesolutions.com



   
ReplyQuote
(@)
Reputable Member
Joined: 18 years ago
Posts: 292
 

Use the west system like Freebird said, and prep the holes like Idonat75 said. West system epoxy bonds much better with polyester resin for repairs like you have to deal with. Use straight West system to wet-out repair then use West system thickened with cab-o-sil to fill holes. Then lightly sand and gel coat. If you have any questions let me know. I run a boatyard and build boats an dknow what works properly the first time.



   
ReplyQuote
James Locke
(@jlocke)
Eminent Member
Joined: 15 years ago
Posts: 25
 

X2 on west systems, more expensive but more reliable. I've patched holes in my two previous Carolina skiffs . I like to let a first wet out coat cure before applying a second wet coat and adding thickened epoxy. That way the 1 st coat really soaks in and seals.



   
ReplyQuote
Fernie Brown
(@)
Prominent Member
Joined: 16 years ago
Posts: 784
 

I like to use that atwood epoxy for things like that. It is sold at walmart in a two part log. Just cut off what you need, mead it for one minute and fill the holes. Good stuff.

Please find it somewhere besides Wal-give 'em 30 million-mart!



   
ReplyQuote
Share: