SWC Forums
Pull up a chair...let's talk fishing.
This spring I will need to purchase a new sonar unit for my beloved Kencraft skiff. I had a raymarineDS500x however parts and support for older models is tough. The main problem I have is that while running greater than about 6kts, the sonar unit loses the return signal and I cannot monitor depth. I have tried adjusting the location, angle, and relative position below the bottom of the hull with no success. I have been told that due to the flat bottom of the hull, and the use of strakes, that air gets trapped and prevents the sonar from operating at speed.
What can be done to overcome this? More wattage? Through hull transducer? Different frequency?
I would appreciate the assistance, as I am buying a new unit this spring.
I am not very familiar with your hull, but through hull transducers generally give better performance at speed than transom mount transducers because they can be mounted where they will run in cleaner/less turbulent water. More wattage is really only a factor for marking the bottom in deeper water.
I have not seen one mounted on a skiff, and I would be a little concerned about having it on the bottom especially if you fish shallow water. I personally run a transom mount 'ducer on my skiff and a through hull on my center console.
If you go on the hull truth and look for semperfifishing (Gil) or BOE Marine (Jim) in the electronics forum, you can contact them with your specific needs and they should be able to provide you your best options. Plus, they have very good pricing.
I have raymarine products (C80/DSM300) and found they are very voltage sensitive.
First question is how old is your battery....try changing that first.
Mine was sensitive to both over and under voltage...needed 'clean' power.
So I ran the positive side straight to the battery switch and the negative
straight to the battery. Seemed to fix the problem. Changed the batteries a year later,
wish I had tried that first before running new wires.
I would lose lock with large power changes, especially from running up on plane
to pulling the engines back to idle. And once messed up, would take 10-15 minutes to
sort itself out. Usually as I was trying to navigate an inlet.
Those dragonfly's look nice for a skiff setup though....
I have never seen a flat bottom hull that would all a depthfinder to read at speed. There seems to be too much turbulence.
I have never seen a flat bottom hull that would all a depthfinder to read at speed. There seems to be too much turbulence.
I have a 19ft skiff. My sonar reads at speeds of up to 23 knots.
It might be the model tho, its a lowrance elite-5 DSI, and the down sensor is long and skinny, unlike most down sensors.
Another thing to check, is after you have launched your boat, or after you have been in real skinny water and may have hit mud/sand, reach down in the water and check to make sure your sensor isnt pointed in some funny angle.....if it is it will not read at speeds or in real skinny water.
Its the hull. Dont start swapping batteries, its not going to help, just waste your money. You can call the maunfacturer of the unit, and tell them your issue and ask what type of bracket to get. also, a good dealer that sells skiffs should also be able to help.
The problem is the design of the hull....yes, its from air bubbles and the sonar cant pick up the right frequencies. Its just the location of the sonar unit. A new bracket will help.
Thanks to all so far. For my electronics I am wired direct to a deep- cycle battery, so although that can do it, it's not the issue. The transducer seems key, and it's location. And I have "done" the hitting bottom thing that Durwyn described. I think the transducer that lowrance uses looks like a solution, but their reputation is a bit scattered for saltwater application. Still looking for the solution.
Lowrance is great for saltwater....their customer service and tech assistance is what sucks. Found that out with mine...
Anyway, PUT A FUSE BETWEEN THE UNIT AND THE BATTERY!!!! If you havnt you can fry all of the unit, or just part of it. Found that out too. Idiot who had the boat before did a shoddy wire job, and after I fried the GPS on my last unit, I found out that there wasnt a fuse there. Kept going on and off, knew I had a short, and found out the hard way.
Anyway, Im not sure if doing a thru hull will solve the problem. Whats the hull type, like length and model? A buddy has carolina skiff and I'll ask him where his units at, but I think he has the same problem.
Durwyn, do you like your lowrance dsi downscan?
Durwyn, do you like your lowrance dsi downscan?
Yea I really like it. I would like one of the new elite 7's but in reality it would be overkill for my 19ft skiff.
The "home runs" for the gps and sonar units are independently fused. I appreciate the continued stream of insights. It gives me a lot to consider. Although there appears to be no simple, single solution, the information provided certainly helps.
Thanks
Call Brian Lovingood at Coastal Mobile Marine. He ONLY works on electronics. I just had him install an Elite 7 HDI on my boat. It is what he is using on his bay boat. Reasonable and comes to you. He came to my marina. 910 713 0014. Close to BC too.

