SWC Forums

Pull up a chair...let's talk fishing.

SeaStar Hydraulic S...
 
Notifications
Clear all

SeaStar Hydraulic Steering

11 Posts
8 Users
0 Reactions
21.8 K Views
John
 John
(@)
Estimable Member
Joined: 16 years ago
Posts: 165
Topic starter   [#33698]

Ok ...let's see how many folks can offer input on this :

I have a 2000 Grady White 273 Chase CC. Last fall I started to notice that the boat would start to drift to the left a little and then when I tried to correct it the steering would turn many times before making any noticeable turn or correction. If I jerk the wheel back to the right the steering acts normal.

After months of bugging my mechanic to look at this he finally looked at it today. The helm appears fine to him with no leaks. He trimmed the motors up and titled or turned them a little to the starboard side to see if they would leak down...of course after about 5-10 minutes the motors were turned all the way towards the starboard side. This was also tried with the port side...motors never moved or "fell" to the port side. I have done some research and have seen that a lot of people are replacing the seals instead of buying a new cylinder. To those with any knowledge of this or experience with this...will replacing the seals fix this problem?
__________________



   
Quote
James White
(@spearjim)
Trusted Member
Joined: 19 years ago
Posts: 71
 

there has been alot of useful info on thehulltruth.com about seastar. just type seastar into tht's search engine and a crap load of threads should pop up.



   
ReplyQuote
Rob DeCola
(@)
Reputable Member
Joined: 13 years ago
Posts: 245
 

I suspect that your piston is worn. It happens when you get old. Flush it with new hydraulic fluid to have maximum viscosity and make sure it's bled well. And, be glad it's not leaking and still steers the girl where she needs to be even if she takes a little coaxing.



   
ReplyQuote
John Rakoci
(@)
Noble Member
Joined: 14 years ago
Posts: 2331
 

After 6 years my system had a lot of play in the wheel and the boat would 'wander' a bit. Over that time 3 - 5 oz of fluid evaporated or went somewhere. My mechanic was at the dock one day and could find no leaks. That fill was 5 months ago -- no problems and system remains full. He said in an emergency use _______ and drain asap. Always use their overpriced fluid--- $22 qt.



   
ReplyQuote
John
 John
(@)
Estimable Member
Joined: 16 years ago
Posts: 165
Topic starter  

Yeah I've always used the SeaStar fluid. I've put the same post on The Hull Truth and I've had a guy tell me replacing the seals will fix this problem. May go ahead and order the kur at work tomorrow and replace them and see if that is the fix.



   
ReplyQuote
William McCann
(@werewolf0711)
Famed Member
Joined: 15 years ago
Posts: 3133
 

Well, yours is probably out of warranty at this point if its the original on the boat. My seals went out with only 2 years on them, coincidentally after I had an autopilot installed on the boat. Anyway, I had to fight with the dealer and talk with seastar myself about the warranty part. Seastar was great to deal with, call them and see if they can get you the answer your looking for. I don't think the motor tilting to one side has anything to do your problem though. Mine has been doing that since new.



   
ReplyQuote
(@curmudgeon)
Noble Member
Joined: 21 years ago
Posts: 1317
 

and I've had a guy tell me replacing the seals will fix this problem.

Assuming you're talking about the end cap seals (and you said nothing about loss of fluid), you would be leaking fluid if the problem was there, and it should 'flop' in both directions if it was the center cylinder seal. I'd have someone revisit the helm after speaking with Seastar ... :chin:



   
ReplyQuote
Frank Smith
(@wildcard)
Noble Member
Joined: 17 years ago
Posts: 1573
 

I know nothing about the subject, but quality of fluid is really important, or so I've heard. I know that I use "Aviation" hydraulic fluid (for better that 35 years), it is ultra-purified. Yes it is exspensive, but you get what you pay for. Inside just about any hydraulic sustem there is a pump, cylinder ( think piston seals), relief and regulating valves. If you do not have a problem with an external leak or air in the system (be honest with yourself here), you may have leakage past the relief valve. I seem to remember that the rudder type system's, had a "relief" pressure of approx 900psi. That would mean, that when a force against the system (against the pressure side) reached 900psi, it would "relieve" the system. Allowing the the system to dump the fluid(because you can't compress fluid, like air) into the sump, to prevent a catistrophic failure. Don't assume the worst, simple troubleshooting will get the job done. Frank



   
ReplyQuote
John
 John
(@)
Estimable Member
Joined: 16 years ago
Posts: 165
Topic starter  

I have talked to Teleflex today and a hydraulic tech guy walked me through some self checks and also said the same thing about the motors should fall to both sides if it was the center seal on the steering ram. I've got the helm seal kit coming and gonna clean it and all the valves and put the new kit on. He seems to feel pretty confident that its the check valve on the helm. Thanks for all the input guys.



   
ReplyQuote
Frank Smith
(@wildcard)
Noble Member
Joined: 17 years ago
Posts: 1573
 

Proof positive,
That a blind squirrel find's an acorn every now and again. On a postive note, it is good that you know more about your steering system. Good luck, Frank



   
ReplyQuote
Matt
 Matt
(@)
Famed Member
Joined: 16 years ago
Posts: 2497
 

Some of those older seastar cylinders were recalled back in 2004. I remember because I had one on the boat I owned at the time. They sent a kit in the mail to fix the issue. I can't remember exactly what the recall was for but it might be worth checking into.



   
ReplyQuote
Share: