SWC Forums

Pull up a chair...let's talk fishing.

Suzuki DF70...Water...
 
Notifications
Clear all

Suzuki DF70...Water on cylinder head?..Anyone heard of this?

15 Posts
9 Users
0 Reactions
46.8 K Views
Brad Wallace
(@)
Active Member
Joined: 14 years ago
Posts: 8
Topic starter   [#29750]

I have my boat at a trusted local marine dealer in the Wilmington area. Took in for service due to loss of power. I received bad news that there was water on the #4 cylinder due to storing engine in upright position. Boat is kept overboard. Can anyone tell me more about this? Does anyone have an interest in helping out with ideas on how to fix it? The marine dealer where it is gave a price of $2500.00!



   
Quote
James White
(@spearjim)
Trusted Member
Joined: 19 years ago
Posts: 71
 

I would start with a compression test of the #4 cylinder.If you have a hole from corrosion in the engine block where water can get in to the intake or exhaust ,It might not be worth fixing to you but it could be as simple as a new head gasket . Its a tough call but head gaskets are not real expensive and you can do them yourself.



   
ReplyQuote
Brad Wallace
(@)
Active Member
Joined: 14 years ago
Posts: 8
Topic starter  

SpearJim. After reading your reply today I contacted the mechanic to see if the compression test was good. He said he never did a compression test. He is basing his conclusion off of water on oil stick and water on cylinder after removing spark plug. I'm not sure that I don't need a second opinion? If compression is good, does that mean cylinder may not be cracked and could only be head gasket? What started this whole thing was a temp sensor failure that put my engine in "safe" mode. That was replaced and when I got my boat back after 3 weeks for that repair, I ran it for no more than 10 mins down ICW to test and that's when I had a loss of power.



   
ReplyQuote
Danny L. Foster
(@)
Reputable Member
Joined: 20 years ago
Posts: 206
 

Do the compression test will tell you if there is a major problem or not, If water got into the cylinder most likely did a lot of damage, rings piston, and maybe the cylinder its self. Blown head gasket could cause both, and so could a bad block,
Dan



   
ReplyQuote
src3
 src3
(@)
Eminent Member
Joined: 16 years ago
Posts: 22
 

And ya can't just replace head gaskets like old school motors, on that 4 stroke ya gotta lift the block.



   
ReplyQuote
James White
(@spearjim)
Trusted Member
Joined: 19 years ago
Posts: 71
 

I think $2500 is just too much to fix the problem if the dealer is not telling you where the water is getting in or if you even have any compression. I would get a second opinion . but If it is as simple as a new head gasket ,its not as hard as you think. I use to back under a tree and pull the power head with a come a long before I finally got new motors. I take it is not under warranty any more.



   
ReplyQuote
Tim elrod
(@)
Noble Member
Joined: 18 years ago
Posts: 1002
 

With "most" modern 4strokes there are cooling passages that will trap and hold water if the engine is stored tilted up. Over the winter the water can freeze and cause cracks in the cylinder wall or in the block itself, or fissures that eventually lead to cracks. "Most" owners manuals instruct you to turn the engine off in the running position and let it sit for a number of minutes (usually 3 to 5) before tilting the engine into the upward position. This is good practice even if the manual does not suggest it.

When I pull my boat out of the water I also tilt the engine back down in the tie down area to allow the saltwater to drain from the block as I am stowing everything. Once it has drained I tilt the engine back up enough to trailer it home. I have noticed a difference in the life of internal zincs and internal corrosion, even though I flush my motor on the hose for 5 minutes after every trip.

With Suzuki outboards this is a more common problem than with Yamaha (IMO) and I always keep my Suzuki's stored in the tilted down or running position.

I am not saying this is your problem, but it is a common problem with modern 4stroke outboards.

Tim



   
ReplyQuote
Bruce MacLachlan
(@bmac)
Eminent Member
Joined: 19 years ago
Posts: 29
 

I'd call Saltwater Marine in Wilmington. They've provided outstanding service to me, and I think they are one of the most experienced Suzuki shops in the country.



   
ReplyQuote
James
(@)
Noble Member
Joined: 20 years ago
Posts: 908
 

Ask him to check the "Engine Holder". Known Suzuki problem with this HP class. Conveniently no recall however. When it fails exhaust and water enter one of the cylinders.



   
ReplyQuote
Bruce MacLachlan
(@bmac)
Eminent Member
Joined: 19 years ago
Posts: 29
 

Ask him to check the "Engine Holder". Known Suzuki problem with this HP class. Conveniently no recall however. When it fails exhaust and water enter one of the cylinders.

Yep. My '05 DF-115 had the engine holder go bad. Cost me about 2000 bucks. I've got over 1100 hours on the motor, and other than that it has been flawless. If Suzuki had notified its customers of the defect, we could have taken preventive measures like replacing that plug before it corrodes completely. I don't know why they didn't do that, but I'm reasonably sure their legal people told them it would be like admitting to product liability. Sorry, for getting off topic. SW Marine took care of it and gave me great service. Motor's running fine after 7 years of pretty heavy use for a weekend warrior.



   
ReplyQuote
Jeff Franklin
(@)
Estimable Member
Joined: 16 years ago
Posts: 180
 

$2500 and no compression test? So he has no idea if it is the block or not at this point.



   
ReplyQuote
Brad Wallace
(@)
Active Member
Joined: 14 years ago
Posts: 8
Topic starter  

Hey Guys. Thanks for the replies. Since I have been away, I have taken different measures. I went to get my boat from the "reputable" dealer/service center. I asked many questions about other possibilities that could have occured. I did ask about the "engine holder" and was promised (and yelled at) that there has never been an "engine holder" go bad on a Suzuki. I took my boat to a a repairman that shares same neighborhood with Donat Marine and several others. He guesses that my new fuel line may have been faulty and corroded even though I run non-ethanol and has caused a blockage in the fuel system, hence the loss of power and cutting out. Whatever happens, I will not be back to the original repair guys. Oh!, I had to pay $45 for them to take out a spark plug and tell me there was water there before they would let me have my boat.
When i get boat fixed I will inform you guys of the cost and problem.



   
ReplyQuote
James
(@)
Noble Member
Joined: 20 years ago
Posts: 908
 

I think if you did a little online research you would find out alot about the engine holder problems. Anyone that denies those does not know enough about Suzuki's to work on them. That problem applies to certain 4 stroke year ranges and horse power classifications but it is a real issue. Ask Garylee on this site about Engine Holders. He can tell you.



   
ReplyQuote
CC
 CC
(@)
Prominent Member
Joined: 20 years ago
Posts: 768
 

I had same problem, a wet plug and milky oil. supposedly, my DF250 had got a little hot and the head gasket warped a hair and that let water into a middle cylinder. it looked nasty when the head was popped off. I was given an astronimical figure to repair it. taking the head off, sending it to a machine shop and to machine flat....it got up to around $6k....for a motor with 800hrs on it......I thinik I got screwed in hind site. I aint posting the details on here. pm me if interested.
CC



   
ReplyQuote
Brad Wallace
(@)
Active Member
Joined: 14 years ago
Posts: 8
Topic starter  

Had oil Changed (did show signs of a little water) and put in new spark plug on #4 cylinder. Compression test was a little weaker on #4 than all others but was in an acceptable range. Put engine on muffs and ran for 30 mins or so. Took boat to ramp and just let enginge run while backed into water. Tale Tale hole was a little weak but cleared up after a few. I decided to unload and boat did fine just "gouging" it in creek. Decided to run ICW and as soon as I got on plain it seems to have lost a cylinder. I am just not convinced that the water is causing this. Has anyone else had this happen in a similar way? How can I make sure all water is removed from oil when I drain it?

Thanks. Gonna make this boat work somehow before trout season heats up!!



   
ReplyQuote
Share: