SWC Forums
Pull up a chair...let's talk fishing.
From all the research I've done, Chris Burleson's name seems to always come up for reliable and honest work on Yamahas. Is he still the best guy in the area? I had some major work done on my Yamaha 225s and it was a nightmare to say the least from a gentlemen that "came highly recommended"....don't know that I have the money or patience to deal with something like that again. Any help would be appreciated!
I am not sure were you are located but Bob Dumong from Sims NC is the best I know on these engines Sims is located close to Wilson his number is 252 373 1962 https://www.facebook.com/buckhorn.boatdoc?fref=ts
I should have clarified that I am in Swansboro so anywhere from Topsail/Sneads Ferry to Morehead/Beaufort would be where I am looking. Thanks for the input!
I am not sure were you are located but Bob Dumong from Sims NC is the best I know on these engines Sims is located close to Wilson his number is 252 373 1962 https://www.facebook.com/buckhorn.boatdoc?fref=ts
My father-in-law recently had his twin 150s serviced and the tilt trim replaced on one of the motors by Bob. He did a great job and was reasonable on price. However, he did suggest that my father-in-law not invest in trim tabs for his 25' KenCraft saying that the motors provide all the trim that he needs. So, I would not take seamanship advice from him. Also, he has moved his shop to the Rock Ridge area directly on hwy 42.
Clay Gaskill on Harkers Island road is sharp.
I get my routine maintenance done at a place closer to my house, but Burleson gets the hard stuff. He'll get it done right. Small shop and always seems to have a backlog of boats so I would call first.
I would highly recommend Bob Dumong, aka Buckhorn Boat Doc. I have a 96 19' Carolina Skifff with a 96 70 horse Evinrude that I bought about a year and half ago that needed some work. I redid the console, rewired it, tons on the trailer, etc., etc. The motor ran okay, so I knew it needed some help. I went as far as my knowledge would go with 2 stroke outboards, replaced the plugs, fuel pump, and fuel lines, but it still needed some help. I live in Wilson so I took it to S&S here in town. After two trips to him and 2.5 months the only thing he could come up with was rebuild the carbs. When I finally got it back from him it actually ran worse, it knocked off at idle every single time. I saw where Backlash was singing Bob's praises on here so I took it to him. Wish I would have started with him. He found 4 problems the other guy never saw. Bob replaced the intake gasket, head gasket, thermostat(called something else), and needle valves on the carbs the first guy did not replace. Runs like a bat of hell now, even with a family of four with full gear.
We have been having fuel issues with my dad's 22' Edgewater that has a Yamaha OX66 250 on it, so he drug it up here from Sneads Ferry today and we dropped it off with Bob.
He is one of those guys that you can tell actually gives a crap about what he is doing and truely wants you to be happy.
I will sure pull my stuff from Sneads Ferry to Bobs everytime
Give Charles Coates a call right there in Cedar point. 252 342 9914. He will even come to you. You won't be disappointed.
Give Charles Coates a call right there in Cedar point. 252 342 9914. He will even come to you. You won't be disappointed.
Chris is steal one of the best in the area for Yamaha service. He stayed back for a reason.He is the only guy who has ever touch my last 3 sets of yamaha's. He will treat you right.
Clay Gaskill on Harkers Island road is sharp.
I'll second that. Great mechanic and honest too. He has helped me with info over the phone more than once, not too many mechanics will do that.