SWC Forums

Pull up a chair...let's talk fishing.

Connecting planer t...
 
Notifications
Clear all

Connecting planer to bridle

13 Posts
11 Users
0 Reactions
55 K Views
Rich
 Rich
(@squid-row)
Illustrious Member
Joined: 22 years ago
Posts: 4097
Topic starter   [#48061]

I tried my planer rod for the first time the other day and I could not get the planer to set.

I have a bridle and attached to the planer are lines with long line clips.

How long should the line be that goes from the planer to the bridle?



   
Quote
Justin Smith
(@)
Estimable Member
Joined: 13 years ago
Posts: 170
 

you should not need any line. Ditch the long line clips and use a trigger snap attached directly to the planer rings. You can use split rings or wire to crimp it to the rings.



   
ReplyQuote
Gus
 Gus
(@getyasome)
Reputable Member
Joined: 15 years ago
Posts: 365
 

https://www.youtube.com/watch?v=vcNy6lkVBOQ
Watch this vid.



   
ReplyQuote
HighSea
(@)
Eminent Member
Joined: 18 years ago
Posts: 20
 

Just try a double snap swivel on each end of your planer, then connect to each loop of the bridle. Also, what size planer are you usig? If too small, the weight of your leader and rig may prevent it from setting.

http://www.tackledirect.com/sea-striker-double-snap-swivel.html



   
ReplyQuote
Nathan
(@ntbrinkl)
Reputable Member
Joined: 13 years ago
Posts: 216
 

If you are having trouble sometimes slowing down a bit will help. Also hold it a little further forward so it gets a second to get in the water before the line catches. One more thing, slowly apply the drag. Don't just snap it shut that will trip it.



   
ReplyQuote
Mark Cogdell
(@markc)
Reputable Member
Joined: 20 years ago
Posts: 211
 

2nd on using brass trigger snaps. If you make your leads with the snaps from the planer a little longer and then build a bridle where the loops are far enough apart to allow the planer to operate like it should (set and trip easily). I am headed over to the boat in a little while, I can take a few pictures of my setup if you want to see how I run mine.



   
ReplyQuote
John
 John
(@)
Famed Member
Joined: 20 years ago
Posts: 3801
 

Rich,
This shows what it should look like.
Make sure the loops are not so far apart that when a fish hooks up you end up pulling on the planner and not the main line. This one will set every time, and you can trip it, by letting line out fast and slamming the drag tight.



   
ReplyQuote
Duane
(@rdnkvet)
Noble Member
Joined: 16 years ago
Posts: 1403
 

I believe clip to clip length should be about an inch longer than the distance between bridle loops.



   
ReplyQuote
Rodney
(@rkforte)
Noble Member
Joined: 14 years ago
Posts: 1072
 

Thanks to Midnight and werewolf, I have mine set up just like Midnight's pic. It works like a charm for my #8 and #12 planers.



   
ReplyQuote
Larry Rowland
(@lwr37)
Famed Member
Joined: 16 years ago
Posts: 2552
 

I believe clip to clip length should be about an inch longer than the distance between bridle loops.

What Duane said above. I run mine a little different. I take the nut off of the bar that pulls the planer and remove the brass ring. Then I put my clip in place of the ring. Off of the back of the planer I use a piece of 400lb mono to connect my back clip to the planer. My planer sets and trips like a champ!

There are many ways to do it and most work just fine.



   
ReplyQuote
Rich
 Rich
(@squid-row)
Illustrious Member
Joined: 22 years ago
Posts: 4097
Topic starter  

Thanks everyone.. I think my set up is right, but the reason I was not able to set the planer might be because I was trying to set it right behind the boat and in the prop wash.

Next time I'll try having it off to the side in cleaner water instead of swirling around behind the keel and rudder



   
ReplyQuote
William McCann
(@werewolf0711)
Famed Member
Joined: 15 years ago
Posts: 3133
 

Here's another video for you to see. They use a quick attach method vs mono or wire to hold the clips on the planer.

http://www.youtube.com/v/YHlx7o_ulAE



   
ReplyQuote
William McCann
(@werewolf0711)
Famed Member
Joined: 15 years ago
Posts: 3133
 

And here's larry's video for easier viewing!
http://www.youtube.com/v/vcNy6lkVBOQ



   
ReplyQuote
Share: